In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Fix running_req for internal abort commands
Disabling the remote phy for a SATA disk causes a hang:
root@(none)$ more /sys/class/sas_phy/phy-0:0:8/target_port_protocols
sata
root@(none)$ echo 0 > sys/class/sas_phy/phy-0:0:8/enable
root@(none)$ [ 67.855950] sas: ex 500e004aaaaaaa1f phy08 change count has changed
[ 67.920585] sd 0:0:2:0: [sdc] Synchronizing SCSI cache
[ 67.925780] sd 0:0:2:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
[ 67.935094] sd 0:0:2:0: [sdc] Stopping disk
[ 67.939305] sd 0:0:2:0: [sdc] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
...
[ 123.998998] INFO: task kworker/u192:1:642 blocked for more than 30 seconds.
[ 124.005960] Not tainted 6.0.0-rc1-205202-gf26f8f761e83 #218
[ 124.012049] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 124.019872] task:kworker/u192:1 state:D stack:0 pid: 642 ppid: 2 flags:0x00000008
[ 124.028223] Workqueue: 0000:04:00.0_event_q sas_port_event_worker
[ 124.034319] Call trace:
[ 124.036758] __switch_to+0x128/0x278
[ 124.040333] __schedule+0x434/0xa58
[ 124.043820] schedule+0x94/0x138
[ 124.047045] schedule_timeout+0x2fc/0x368
[ 124.051052] wait_for_completion+0xdc/0x200
[ 124.055234] __flush_workqueue+0x1a8/0x708
[ 124.059328] sas_porte_broadcast_rcvd+0xa8/0xc0
[ 124.063858] sas_port_event_worker+0x60/0x98
[ 124.068126] process_one_work+0x3f8/0x660
[ 124.072134] worker_thread+0x70/0x700
[ 124.075793] kthread+0x1a4/0x1b8
[ 124.079014] ret_from_fork+0x10/0x20
The issue is that the per-device running_req read in
pm8001_dev_gone_notify() never goes to zero and we never make progress.
This is caused by missing accounting for running_req for when an internal
abort command completes.
In commit 2cbbf489778e ("scsi: pm8001: Use libsas internal abort support")
we started to send internal abort commands as a proper sas_task. In this
when we deliver a sas_task to HW the per-device running_req is incremented
in pm8001_queue_command(). However it is never decremented for internal
abort commnds, so decrement in pm8001_mpi_task_abort_resp().
scsi: pm8001: Fix running_req for internal abort commands
Disabling the remote phy for a SATA disk causes a hang:
root@(none)$ more /sys/class/sas_phy/phy-0:0:8/target_port_protocols
sata
root@(none)$ echo 0 > sys/class/sas_phy/phy-0:0:8/enable
root@(none)$ [ 67.855950] sas: ex 500e004aaaaaaa1f phy08 change count has changed
[ 67.920585] sd 0:0:2:0: [sdc] Synchronizing SCSI cache
[ 67.925780] sd 0:0:2:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
[ 67.935094] sd 0:0:2:0: [sdc] Stopping disk
[ 67.939305] sd 0:0:2:0: [sdc] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
...
[ 123.998998] INFO: task kworker/u192:1:642 blocked for more than 30 seconds.
[ 124.005960] Not tainted 6.0.0-rc1-205202-gf26f8f761e83 #218
[ 124.012049] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 124.019872] task:kworker/u192:1 state:D stack:0 pid: 642 ppid: 2 flags:0x00000008
[ 124.028223] Workqueue: 0000:04:00.0_event_q sas_port_event_worker
[ 124.034319] Call trace:
[ 124.036758] __switch_to+0x128/0x278
[ 124.040333] __schedule+0x434/0xa58
[ 124.043820] schedule+0x94/0x138
[ 124.047045] schedule_timeout+0x2fc/0x368
[ 124.051052] wait_for_completion+0xdc/0x200
[ 124.055234] __flush_workqueue+0x1a8/0x708
[ 124.059328] sas_porte_broadcast_rcvd+0xa8/0xc0
[ 124.063858] sas_port_event_worker+0x60/0x98
[ 124.068126] process_one_work+0x3f8/0x660
[ 124.072134] worker_thread+0x70/0x700
[ 124.075793] kthread+0x1a4/0x1b8
[ 124.079014] ret_from_fork+0x10/0x20
The issue is that the per-device running_req read in
pm8001_dev_gone_notify() never goes to zero and we never make progress.
This is caused by missing accounting for running_req for when an internal
abort command completes.
In commit 2cbbf489778e ("scsi: pm8001: Use libsas internal abort support")
we started to send internal abort commands as a proper sas_task. In this
when we deliver a sas_task to HW the per-device running_req is incremented
in pm8001_queue_command(). However it is never decremented for internal
abort commnds, so decrement in pm8001_mpi_task_abort_resp().
Default status is the baseline for the product, each version can override it (e.g. patched versions marked unaffected).
| Vendor | Product | Default status | Versions | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Linux | Linux | unaffected |
|
||||||||||||||||||
| Linux | Linux | affected |
|
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Wed, 31 Dec 2025 12:15:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| References |
| |
| Metrics |
threat_severity
|
cvssV3_1
|
Tue, 30 Dec 2025 12:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: scsi: pm8001: Fix running_req for internal abort commands Disabling the remote phy for a SATA disk causes a hang: root@(none)$ more /sys/class/sas_phy/phy-0:0:8/target_port_protocols sata root@(none)$ echo 0 > sys/class/sas_phy/phy-0:0:8/enable root@(none)$ [ 67.855950] sas: ex 500e004aaaaaaa1f phy08 change count has changed [ 67.920585] sd 0:0:2:0: [sdc] Synchronizing SCSI cache [ 67.925780] sd 0:0:2:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK [ 67.935094] sd 0:0:2:0: [sdc] Stopping disk [ 67.939305] sd 0:0:2:0: [sdc] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK ... [ 123.998998] INFO: task kworker/u192:1:642 blocked for more than 30 seconds. [ 124.005960] Not tainted 6.0.0-rc1-205202-gf26f8f761e83 #218 [ 124.012049] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 124.019872] task:kworker/u192:1 state:D stack:0 pid: 642 ppid: 2 flags:0x00000008 [ 124.028223] Workqueue: 0000:04:00.0_event_q sas_port_event_worker [ 124.034319] Call trace: [ 124.036758] __switch_to+0x128/0x278 [ 124.040333] __schedule+0x434/0xa58 [ 124.043820] schedule+0x94/0x138 [ 124.047045] schedule_timeout+0x2fc/0x368 [ 124.051052] wait_for_completion+0xdc/0x200 [ 124.055234] __flush_workqueue+0x1a8/0x708 [ 124.059328] sas_porte_broadcast_rcvd+0xa8/0xc0 [ 124.063858] sas_port_event_worker+0x60/0x98 [ 124.068126] process_one_work+0x3f8/0x660 [ 124.072134] worker_thread+0x70/0x700 [ 124.075793] kthread+0x1a4/0x1b8 [ 124.079014] ret_from_fork+0x10/0x20 The issue is that the per-device running_req read in pm8001_dev_gone_notify() never goes to zero and we never make progress. This is caused by missing accounting for running_req for when an internal abort command completes. In commit 2cbbf489778e ("scsi: pm8001: Use libsas internal abort support") we started to send internal abort commands as a proper sas_task. In this when we deliver a sas_task to HW the per-device running_req is incremented in pm8001_queue_command(). However it is never decremented for internal abort commnds, so decrement in pm8001_mpi_task_abort_resp(). | |
| Title | scsi: pm8001: Fix running_req for internal abort commands | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2025-12-30T12:08:33.548Z
Reserved: 2025-12-30T12:06:07.131Z
Link: CVE-2022-50818
Vulnrichment
No data.
NVD
Status : Awaiting Analysis
Published: 2025-12-30T13:15:56.200
Modified: 2025-12-31T20:43:05.160
Link: CVE-2022-50818
Redhat
OpenCVE Enrichment
No data.
Weaknesses
No weakness.