| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
s390/sclp: Prevent release of buffer in I/O
When a task waiting for completion of a Store Data operation is
interrupted, an attempt is made to halt this operation. If this attempt
fails due to a hardware or firmware problem, there is a chance that the
SCLP facility might store data into buffers referenced by the original
operation at a later time.
Handle this situation by not releasing the referenced data buffers if
the halt attempt fails. For current use cases, this might result in a
leak of few pages of memory in case of a rare hardware/firmware
malfunction. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix quota root leak after quota disable failure
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix memory leak in nfs4_set_security_label
We leak nfs_fattr and nfs4_label every time we set a security xattr. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmvnic: Add tx check to prevent skb leak
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/exynos/vidi: fix memory leak in .get_modes()
The duplicated EDID is never freed. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/hwmon: Get rid of devm
When both hwmon and hwmon drvdata (on which hwmon depends) are device
managed resources, the expectation, on device unbind, is that hwmon will be
released before drvdata. However, in i915 there are two separate code
paths, which both release either drvdata or hwmon and either can be
released before the other. These code paths (for device unbind) are as
follows (see also the bug referenced below):
Call Trace:
release_nodes+0x11/0x70
devres_release_group+0xb2/0x110
component_unbind_all+0x8d/0xa0
component_del+0xa5/0x140
intel_pxp_tee_component_fini+0x29/0x40 [i915]
intel_pxp_fini+0x33/0x80 [i915]
i915_driver_remove+0x4c/0x120 [i915]
i915_pci_remove+0x19/0x30 [i915]
pci_device_remove+0x32/0xa0
device_release_driver_internal+0x19c/0x200
unbind_store+0x9c/0xb0
and
Call Trace:
release_nodes+0x11/0x70
devres_release_all+0x8a/0xc0
device_unbind_cleanup+0x9/0x70
device_release_driver_internal+0x1c1/0x200
unbind_store+0x9c/0xb0
This means that in i915, if use devm, we cannot gurantee that hwmon will
always be released before drvdata. Which means that we have a uaf if hwmon
sysfs is accessed when drvdata has been released but hwmon hasn't.
The only way out of this seems to be do get rid of devm_ and release/free
everything explicitly during device unbind.
v2: Change commit message and other minor code changes
v3: Cleanup from i915_hwmon_register on error (Armin Wolf)
v4: Eliminate potential static analyzer warning (Rodrigo)
Eliminate fetch_and_zero (Jani)
v5: Restore previous logic for ddat_gt->hwmon_dev error return (Andi) |
| In the Linux kernel, the following vulnerability has been resolved:
hv_netvsc: Don't free decrypted memory
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The netvsc driver could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the gpadl
to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
uio_hv_generic: Don't free decrypted memory
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The VMBus device UIO driver could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the gpadl
to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: vmbus: Don't free ring buffers that couldn't be re-encrypted
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The VMBus ring buffer code could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the struct
vmbus_gpadl for the ring buffers to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: uhci: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: pcn_uart: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/iommu: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: fix potential memory leaks in session setup
Make sure to free cifs_ses::auth_key.response before allocating it as
we might end up leaking memory in reconnect or mounting. |
| In the Linux kernel, the following vulnerability has been resolved:
media: imon: fix access to invalid resource for the second interface
imon driver probes two USB interfaces, and at the probe of the second
interface, the driver assumes blindly that the first interface got
bound with the same imon driver. It's usually true, but it's still
possible that the first interface is bound with another driver via a
malformed descriptor. Then it may lead to a memory corruption, as
spotted by syzkaller; imon driver accesses the data from drvdata as
struct imon_context object although it's a completely different one
that was assigned by another driver.
This patch adds a sanity check -- whether the first interface is
really bound with the imon driver or not -- for avoiding the problem
above at the probe time. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix slab-out-of-bounds Read in dtSearch
Currently while searching for current page in the sorted entry table
of the page there is a out of bound access. Added a bound check to fix
the error.
Dave:
Set return code to -EIO |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm80xx: Avoid leaking tags when processing OPC_INB_SET_CONTROLLER_CONFIG command
Tags allocated for OPC_INB_SET_CONTROLLER_CONFIG command need to be freed
when we receive the response. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range
When running an SVA case, the following soft lockup is triggered:
--------------------------------------------------------------------
watchdog: BUG: soft lockup - CPU#244 stuck for 26s!
pstate: 83400009 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : arm_smmu_cmdq_issue_cmdlist+0x178/0xa50
lr : arm_smmu_cmdq_issue_cmdlist+0x150/0xa50
sp : ffff8000d83ef290
x29: ffff8000d83ef290 x28: 000000003b9aca00 x27: 0000000000000000
x26: ffff8000d83ef3c0 x25: da86c0812194a0e8 x24: 0000000000000000
x23: 0000000000000040 x22: ffff8000d83ef340 x21: ffff0000c63980c0
x20: 0000000000000001 x19: ffff0000c6398080 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: ffff3000b4a3bbb0
x14: ffff3000b4a30888 x13: ffff3000b4a3cf60 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc08120e4d6bc
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000048cfa
x5 : 0000000000000000 x4 : 0000000000000001 x3 : 000000000000000a
x2 : 0000000080000000 x1 : 0000000000000000 x0 : 0000000000000001
Call trace:
arm_smmu_cmdq_issue_cmdlist+0x178/0xa50
__arm_smmu_tlb_inv_range+0x118/0x254
arm_smmu_tlb_inv_range_asid+0x6c/0x130
arm_smmu_mm_invalidate_range+0xa0/0xa4
__mmu_notifier_invalidate_range_end+0x88/0x120
unmap_vmas+0x194/0x1e0
unmap_region+0xb4/0x144
do_mas_align_munmap+0x290/0x490
do_mas_munmap+0xbc/0x124
__vm_munmap+0xa8/0x19c
__arm64_sys_munmap+0x28/0x50
invoke_syscall+0x78/0x11c
el0_svc_common.constprop.0+0x58/0x1c0
do_el0_svc+0x34/0x60
el0_svc+0x2c/0xd4
el0t_64_sync_handler+0x114/0x140
el0t_64_sync+0x1a4/0x1a8
--------------------------------------------------------------------
Note that since 6.6-rc1 the arm_smmu_mm_invalidate_range above is renamed
to "arm_smmu_mm_arch_invalidate_secondary_tlbs", yet the problem remains.
The commit 06ff87bae8d3 ("arm64: mm: remove unused functions and variable
protoypes") fixed a similar lockup on the CPU MMU side. Yet, it can occur
to SMMU too, since arm_smmu_mm_arch_invalidate_secondary_tlbs() is called
typically next to MMU tlb flush function, e.g.
tlb_flush_mmu_tlbonly {
tlb_flush {
__flush_tlb_range {
// check MAX_TLBI_OPS
}
}
mmu_notifier_arch_invalidate_secondary_tlbs {
arm_smmu_mm_arch_invalidate_secondary_tlbs {
// does not check MAX_TLBI_OPS
}
}
}
Clone a CMDQ_MAX_TLBI_OPS from the MAX_TLBI_OPS in tlbflush.h, since in an
SVA case SMMU uses the CPU page table, so it makes sense to align with the
tlbflush code. Then, replace per-page TLBI commands with a single per-asid
TLBI command, if the request size hits this threshold. |
| An issue in the Bluetooth firmware of JXL 9 Inch Car Android Double Din Player Android v12.0 allows attackers to cause a Denial of Service (DoS) via sending a crafted Link Manager Protocol (LMP) packet. |
| Turms AI-Serving module v0.10.0-SNAPSHOT and earlier contains an image decompression bomb denial of service vulnerability. The ExtendedOpenCVImage class in ai/djl/opencv/ExtendedOpenCVImage.java loads images using OpenCV's imread() function without validating dimensions or pixel count before decompression. An attacker can upload a specially crafted compressed image file (e.g., PNG) that is small when compressed but expands to gigabytes of memory when loaded. This causes immediate memory exhaustion, OutOfMemoryError, and service crash. No authentication is required if the OCR service is publicly accessible. Multiple requests can completely deny service availability. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: usbhid: fix info leak in hid_submit_ctrl
In hid_submit_ctrl(), the way of calculating the report length doesn't
take into account that report->size can be zero. When running the
syzkaller reproducer, a report of size 0 causes hid_submit_ctrl) to
calculate transfer_buffer_length as 16384. When this urb is passed to
the usb core layer, KMSAN reports an info leak of 16384 bytes.
To fix this, first modify hid_report_len() to account for the zero
report size case by using DIV_ROUND_UP for the division. Then, call it
from hid_submit_ctrl(). |
