| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To check if the device has high CPU load due to this issue, the administrator can issue the following command: user@host> show chassis routing-engine Routing Engine status: ... Idle 2 percent the "Idle" value shows as low (2 % in the example above), and also the following command: user@host> show system processes summary ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 11639 root 52 0 283M 11296K select 12:15 44.97% eventd 11803 root 81 0 719M 239M RUN 251:12 31.98% fxpc{fxpc} the eventd and the fxpc processes might use higher WCPU percentage (respectively 44.97% and 31.98% in the above example). This issue affects Juniper Networks Junos OS on EX2300 Series: 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. |
| On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases. |
| On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of specific layer 2 frame, an attacker connected to the same broadcast domain can repeatedly crash the PFE, causing a prolonged Denial of Service (DoS). This issue affects Juniper Networks Junos OS on MX Series: 17.2 versions prior to 17.2R3-S4; 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. This issue does not affect Juniper Networks Junos OS releases prior to 17.2R1. |
| The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1. |
| Specific IPv6 packets sent by clients processed by the Routing Engine (RE) are improperly handled. These IPv6 packets are designed to be blocked by the RE from egressing the RE. Instead, the RE allows these specific IPv6 packets to egress the RE, at which point a mbuf memory leak occurs within the Juniper Networks Junos OS device. This memory leak eventually leads to a kernel crash (vmcore), or the device hanging and requiring a power cycle to restore service, creating a Denial of Service (DoS) condition. During the time where mbufs are rising, yet not fully filled, some traffic from client devices may begin to be black holed. To be black holed, this traffic must match the condition where this traffic must be processed by the RE. Continued receipt and attempted egress of these specific IPv6 packets from the Routing Engine (RE) will create an extended Denial of Service (DoS) condition. Scenarios which have been observed are: 1. In a single chassis, single RE scenario, the device will hang without vmcore, or a vmcore may occur and then hang. In this scenario the device needs to be power cycled. 2. In a single chassis, dual RE scenario, the device master RE will fail over to the backup RE. In this scenario, the master and the backup REs need to be reset from time to time when they vmcore. There is no need to power cycle the device. 3. In a dual chassis, single RE scenario, the device will hang without vmcore, or a vmcore may occur and then hang. In this scenario, the two chassis' design relies upon some type of network level redundancy - VRRP, GRES, NSR, etc. - 3.a In a commanded switchover, where nonstop active routing (NSR) is enabled no session loss is observed. 4. In a dual chassis, dual chassis scenario, rely upon the RE to RE failover as stated in the second scenario. In the unlikely event that the device does not switch RE to RE gracefully, then the fallback position is to the network level services scenario in the third scenario. This issue affects: Juniper Networks Junos OS 16.1 versions prior to 16.1R7-S6; 16.1 version 16.1X70-D10 and later; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D50, 18.2X75-D410; 18.3 versions prior to 18.3R1-S6, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect releases prior to Junos OS 16.1R1. |
| In a Point-to-Multipoint (P2MP) Label Switched Path (LSP) scenario, an uncontrolled resource consumption vulnerability in the Routing Protocol Daemon (RPD) in Juniper Networks Junos OS allows a specific SNMP request to trigger an infinite loop causing a high CPU usage Denial of Service (DoS) condition. This issue affects both SNMP over IPv4 and IPv6. This issue affects: Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D90; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D238, 15.1X53-D592; 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R3-S2; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2. |
| A denial of service vulnerability exists when ASP.NET Core improperly handles web requests, aka 'ASP.NET Core Denial of Service Vulnerability'. |
| An issue was discovered in binutils libbfd.c 2.36 relating to the auxiliary symbol data allows attackers to read or write to system memory or cause a denial of service. |
| A memory consumption issue in get_data function in binutils/nm.c in GNU nm before 2.34 allows attackers to cause a denial of service via crafted command. |
| A buffer overflow vulnerability in the Databuf function in types.cpp of Exiv2 v0.27.1 leads to a denial of service (DOS). |
| Buffer Overflow vulnerability in HtmlOutputDev::page in poppler 0.75.0 allows attackers to cause a denial of service. |
| Mitsubishi MELSEC iQ-R Series PLCs with firmware 49 allow an unauthenticated attacker to halt the industrial process by sending a crafted packet over the network. This denial of service attack exposes Improper Input Validation. After halting, physical access to the PLC is required in order to restore production, and the device state is lost. This is related to R04CPU, RJ71GF11-T2, R04CPU, and RJ71GF11-T2. |
| An attacker could send a specially crafted packet that could have CodeMeter (All versions prior to 7.10) send back packets containing data from the heap. |
| It is possible for an unauthenticated remote DCOM websocket connection to crash the Command Centre service's DCOM websocket thread due to improper shutdown of closed websocket connections, preventing it from accepting future DCOM websocket (Configuration Client) connections. Affected versions are v8.20 prior to v8.20.1166(MR3), v8.10 prior to v8.10.1211(MR5), v8.00 prior to v8.00.1228(MR6), all versions of 7.90 and earlier. |
| CODESYS Control runtime system before 3.5.16.10 allows Uncontrolled Memory Allocation. |
| A vulnerability has been identified in SIMATIC S7-300 CPU family (incl. related ET200 CPUs and SIPLUS variants) (All versions), SIMATIC TDC CPU555 (All versions), SINUMERIK 840D sl (All versions). Sending multiple specially crafted packets to the affected devices could cause a Denial-of-Service on port 102. A cold restart is required to recover the service. |
| An issue was discovered in Xen through 4.13.x, allowing x86 Intel HVM guest OS users to cause a host OS denial of service or possibly gain privileges because of insufficient cache write-back under VT-d. When page tables are shared between IOMMU and CPU, changes to them require flushing of both TLBs. Furthermore, IOMMUs may be non-coherent, and hence prior to flushing IOMMU TLBs, a CPU cache also needs writing back to memory after changes were made. Such writing back of cached data was missing in particular when splitting large page mappings into smaller granularity ones. A malicious guest may be able to retain read/write DMA access to frames returned to Xen's free pool, and later reused for another purpose. Host crashes (leading to a Denial of Service) and privilege escalation cannot be ruled out. Xen versions from at least 3.2 onwards are affected. Only x86 Intel systems are affected. x86 AMD as well as Arm systems are not affected. Only x86 HVM guests using hardware assisted paging (HAP), having a passed through PCI device assigned, and having page table sharing enabled can leverage the vulnerability. Note that page table sharing will be enabled (by default) only if Xen considers IOMMU and CPU large page size support compatible. |
| In the Linux kernel 4.4 through 5.7.6, usbtest_disconnect in drivers/usb/misc/usbtest.c has a memory leak, aka CID-28ebeb8db770. |
| Crossbeam is a set of tools for concurrent programming. In crossbeam-channel before version 0.4.4, the bounded channel incorrectly assumes that `Vec::from_iter` has allocated capacity that same as the number of iterator elements. `Vec::from_iter` does not actually guarantee that and may allocate extra memory. The destructor of the `bounded` channel reconstructs `Vec` from the raw pointer based on the incorrect assumes described above. This is unsound and causing deallocation with the incorrect capacity when `Vec::from_iter` has allocated different sizes with the number of iterator elements. This has been fixed in crossbeam-channel 0.4.4. |
| In Helm before versions 2.16.11 and 3.3.2 there is a bug in which the `alias` field on a `Chart.yaml` is not properly sanitized. This could lead to the injection of unwanted information into a chart. This issue has been patched in Helm 3.3.2 and 2.16.11. A possible workaround is to manually review the `dependencies` field of any untrusted chart, verifying that the `alias` field is either not used, or (if used) does not contain newlines or path characters. |
