| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/iommu: Fix notifiers being shared by PCI and VIO buses
fail_iommu_setup() registers the fail_iommu_bus_notifier struct to both
PCI and VIO buses. struct notifier_block is a linked list node, so this
causes any notifiers later registered to either bus type to also be
registered to the other since they share the same node.
This causes issues in (at least) the vgaarb code, which registers a
notifier for PCI buses. pci_notify() ends up being called on a vio
device, converted with to_pci_dev() even though it's not a PCI device,
and finally makes a bad access in vga_arbiter_add_pci_device() as
discovered with KASAN:
BUG: KASAN: slab-out-of-bounds in vga_arbiter_add_pci_device+0x60/0xe00
Read of size 4 at addr c000000264c26fdc by task swapper/0/1
Call Trace:
dump_stack_lvl+0x1bc/0x2b8 (unreliable)
print_report+0x3f4/0xc60
kasan_report+0x244/0x698
__asan_load4+0xe8/0x250
vga_arbiter_add_pci_device+0x60/0xe00
pci_notify+0x88/0x444
notifier_call_chain+0x104/0x320
blocking_notifier_call_chain+0xa0/0x140
device_add+0xac8/0x1d30
device_register+0x58/0x80
vio_register_device_node+0x9ac/0xce0
vio_bus_scan_register_devices+0xc4/0x13c
__machine_initcall_pseries_vio_device_init+0x94/0xf0
do_one_initcall+0x12c/0xaa8
kernel_init_freeable+0xa48/0xba8
kernel_init+0x64/0x400
ret_from_kernel_thread+0x5c/0x64
Fix this by creating separate notifier_block structs for each bus type.
[mpe: Add #ifdef to fix CONFIG_IBMVIO=n build] |
| In the Linux kernel, the following vulnerability has been resolved:
net: prevent skb corruption on frag list segmentation
Ian reported several skb corruptions triggered by rx-gro-list,
collecting different oops alike:
[ 62.624003] BUG: kernel NULL pointer dereference, address: 00000000000000c0
[ 62.631083] #PF: supervisor read access in kernel mode
[ 62.636312] #PF: error_code(0x0000) - not-present page
[ 62.641541] PGD 0 P4D 0
[ 62.644174] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 62.648629] CPU: 1 PID: 913 Comm: napi/eno2-79 Not tainted 6.4.0 #364
[ 62.655162] Hardware name: Supermicro Super Server/A2SDi-12C-HLN4F, BIOS 1.7a 10/13/2022
[ 62.663344] RIP: 0010:__udp_gso_segment (./include/linux/skbuff.h:2858
./include/linux/udp.h:23 net/ipv4/udp_offload.c:228 net/ipv4/udp_offload.c:261
net/ipv4/udp_offload.c:277)
[ 62.687193] RSP: 0018:ffffbd3a83b4f868 EFLAGS: 00010246
[ 62.692515] RAX: 00000000000000ce RBX: 0000000000000000 RCX: 0000000000000000
[ 62.699743] RDX: ffffa124def8a000 RSI: 0000000000000079 RDI: ffffa125952a14d4
[ 62.706970] RBP: ffffa124def8a000 R08: 0000000000000022 R09: 00002000001558c9
[ 62.714199] R10: 0000000000000000 R11: 00000000be554639 R12: 00000000000000e2
[ 62.721426] R13: ffffa125952a1400 R14: ffffa125952a1400 R15: 00002000001558c9
[ 62.728654] FS: 0000000000000000(0000) GS:ffffa127efa40000(0000)
knlGS:0000000000000000
[ 62.736852] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 62.742702] CR2: 00000000000000c0 CR3: 00000001034b0000 CR4: 00000000003526e0
[ 62.749948] Call Trace:
[ 62.752498] <TASK>
[ 62.779267] inet_gso_segment (net/ipv4/af_inet.c:1398)
[ 62.787605] skb_mac_gso_segment (net/core/gro.c:141)
[ 62.791906] __skb_gso_segment (net/core/dev.c:3403 (discriminator 2))
[ 62.800492] validate_xmit_skb (./include/linux/netdevice.h:4862
net/core/dev.c:3659)
[ 62.804695] validate_xmit_skb_list (net/core/dev.c:3710)
[ 62.809158] sch_direct_xmit (net/sched/sch_generic.c:330)
[ 62.813198] __dev_queue_xmit (net/core/dev.c:3805 net/core/dev.c:4210)
net/netfilter/core.c:626)
[ 62.821093] br_dev_queue_push_xmit (net/bridge/br_forward.c:55)
[ 62.825652] maybe_deliver (net/bridge/br_forward.c:193)
[ 62.829420] br_flood (net/bridge/br_forward.c:233)
[ 62.832758] br_handle_frame_finish (net/bridge/br_input.c:215)
[ 62.837403] br_handle_frame (net/bridge/br_input.c:298
net/bridge/br_input.c:416)
[ 62.851417] __netif_receive_skb_core.constprop.0 (net/core/dev.c:5387)
[ 62.866114] __netif_receive_skb_list_core (net/core/dev.c:5570)
[ 62.871367] netif_receive_skb_list_internal (net/core/dev.c:5638
net/core/dev.c:5727)
[ 62.876795] napi_complete_done (./include/linux/list.h:37
./include/net/gro.h:434 ./include/net/gro.h:429 net/core/dev.c:6067)
[ 62.881004] ixgbe_poll (drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3191)
[ 62.893534] __napi_poll (net/core/dev.c:6498)
[ 62.897133] napi_threaded_poll (./include/linux/netpoll.h:89
net/core/dev.c:6640)
[ 62.905276] kthread (kernel/kthread.c:379)
[ 62.913435] ret_from_fork (arch/x86/entry/entry_64.S:314)
[ 62.917119] </TASK>
In the critical scenario, rx-gro-list GRO-ed packets are fed, via a
bridge, both to the local input path and to an egress device (tun).
The segmentation of such packets unsafely writes to the cloned skbs
with shared heads.
This change addresses the issue by uncloning as needed the
to-be-segmented skbs. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.
The process is as follows:
setup_net()
ops_init()
data = kzalloc(...) ---> alloc "data"
net_assign_generic() ---> assign "date" to ptr in net->gen
...
ops->init() ---> failed
...
kfree(data); ---> ptr in net->gen is invalid
...
ops_exit_list()
...
nfqnl_nf_hook_drop()
*q = nfnl_queue_pernet(net) ---> q is invalid
The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
Allocated by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0xa1/0xb0
__kmalloc+0x49/0xb0
ops_init+0xe7/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x155/0x1b0
slab_free_freelist_hook+0x11b/0x220
__kmem_cache_free+0xa4/0x360
ops_init+0xb9/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pv: fix index value of replaced ASCE
The index field of the struct page corresponding to a guest ASCE should
be 0. When replacing the ASCE in s390_replace_asce(), the index of the
new ASCE should also be set to 0.
Having the wrong index might lead to the wrong addresses being passed
around when notifying pte invalidations, and eventually to validity
intercepts (VM crash) if the prefix gets unmapped and the notifier gets
called with the wrong address. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/client: Fix memory leak in drm_client_target_cloned
dmt_mode is allocated and never freed in this function.
It was found with the ast driver, but most drivers using generic fbdev
setup are probably affected.
This fixes the following kmemleak report:
backtrace:
[<00000000b391296d>] drm_mode_duplicate+0x45/0x220 [drm]
[<00000000e45bb5b3>] drm_client_target_cloned.constprop.0+0x27b/0x480 [drm]
[<00000000ed2d3a37>] drm_client_modeset_probe+0x6bd/0xf50 [drm]
[<0000000010e5cc9d>] __drm_fb_helper_initial_config_and_unlock+0xb4/0x2c0 [drm_kms_helper]
[<00000000909f82ca>] drm_fbdev_client_hotplug+0x2bc/0x4d0 [drm_kms_helper]
[<00000000063a69aa>] drm_client_register+0x169/0x240 [drm]
[<00000000a8c61525>] ast_pci_probe+0x142/0x190 [ast]
[<00000000987f19bb>] local_pci_probe+0xdc/0x180
[<000000004fca231b>] work_for_cpu_fn+0x4e/0xa0
[<0000000000b85301>] process_one_work+0x8b7/0x1540
[<000000003375b17c>] worker_thread+0x70a/0xed0
[<00000000b0d43cd9>] kthread+0x29f/0x340
[<000000008d770833>] ret_from_fork+0x1f/0x30
unreferenced object 0xff11000333089a00 (size 128): |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbe: Fix panic during XDP_TX with > 64 CPUs
Commit 4fe815850bdc ("ixgbe: let the xdpdrv work with more than 64 cpus")
adds support to allow XDP programs to run on systems with more than
64 CPUs by locking the XDP TX rings and indexing them using cpu % 64
(IXGBE_MAX_XDP_QS).
Upon trying this out patch on a system with more than 64 cores,
the kernel paniced with an array-index-out-of-bounds at the return in
ixgbe_determine_xdp_ring in ixgbe.h, which means ixgbe_determine_xdp_q_idx
was just returning the cpu instead of cpu % IXGBE_MAX_XDP_QS. An example
splat:
==========================================================================
UBSAN: array-index-out-of-bounds in
/var/lib/dkms/ixgbe/5.18.6+focal-1/build/src/ixgbe.h:1147:26
index 65 is out of range for type 'ixgbe_ring *[64]'
==========================================================================
BUG: kernel NULL pointer dereference, address: 0000000000000058
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 65 PID: 408 Comm: ksoftirqd/65
Tainted: G IOE 5.15.0-48-generic #54~20.04.1-Ubuntu
Hardware name: Dell Inc. PowerEdge R640/0W23H8, BIOS 2.5.4 01/13/2020
RIP: 0010:ixgbe_xmit_xdp_ring+0x1b/0x1c0 [ixgbe]
Code: 3b 52 d4 cf e9 42 f2 ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 55 b9
00 00 00 00 48 89 e5 41 57 41 56 41 55 41 54 53 48 83 ec 08 <44> 0f b7
47 58 0f b7 47 5a 0f b7 57 54 44 0f b7 76 08 66 41 39 c0
RSP: 0018:ffffbc3fcd88fcb0 EFLAGS: 00010282
RAX: ffff92a253260980 RBX: ffffbc3fe68b00a0 RCX: 0000000000000000
RDX: ffff928b5f659000 RSI: ffff928b5f659000 RDI: 0000000000000000
RBP: ffffbc3fcd88fce0 R08: ffff92b9dfc20580 R09: 0000000000000001
R10: 3d3d3d3d3d3d3d3d R11: 3d3d3d3d3d3d3d3d R12: 0000000000000000
R13: ffff928b2f0fa8c0 R14: ffff928b9be20050 R15: 000000000000003c
FS: 0000000000000000(0000) GS:ffff92b9dfc00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 000000011dd6a002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
ixgbe_poll+0x103e/0x1280 [ixgbe]
? sched_clock_cpu+0x12/0xe0
__napi_poll+0x30/0x160
net_rx_action+0x11c/0x270
__do_softirq+0xda/0x2ee
run_ksoftirqd+0x2f/0x50
smpboot_thread_fn+0xb7/0x150
? sort_range+0x30/0x30
kthread+0x127/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x1f/0x30
</TASK>
I think this is how it happens:
Upon loading the first XDP program on a system with more than 64 CPUs,
ixgbe_xdp_locking_key is incremented in ixgbe_xdp_setup. However,
immediately after this, the rings are reconfigured by ixgbe_setup_tc.
ixgbe_setup_tc calls ixgbe_clear_interrupt_scheme which calls
ixgbe_free_q_vectors which calls ixgbe_free_q_vector in a loop.
ixgbe_free_q_vector decrements ixgbe_xdp_locking_key once per call if
it is non-zero. Commenting out the decrement in ixgbe_free_q_vector
stopped my system from panicing.
I suspect to make the original patch work, I would need to load an XDP
program and then replace it in order to get ixgbe_xdp_locking_key back
above 0 since ixgbe_setup_tc is only called when transitioning between
XDP and non-XDP ring configurations, while ixgbe_xdp_locking_key is
incremented every time ixgbe_xdp_setup is called.
Also, ixgbe_setup_tc can be called via ethtool --set-channels, so this
becomes another path to decrement ixgbe_xdp_locking_key to 0 on systems
with more than 64 CPUs.
Since ixgbe_xdp_locking_key only protects the XDP_TX path and is tied
to the number of CPUs present, there is no reason to disable it upon
unloading an XDP program. To avoid confusion, I have moved enabling
ixgbe_xdp_locking_key into ixgbe_sw_init, which is part of the probe path. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_pmem: add the missing REQ_OP_WRITE for flush bio
When doing mkfs.xfs on a pmem device, the following warning was
------------[ cut here ]------------
WARNING: CPU: 2 PID: 384 at block/blk-core.c:751 submit_bio_noacct
Modules linked in:
CPU: 2 PID: 384 Comm: mkfs.xfs Not tainted 6.4.0-rc7+ #154
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:submit_bio_noacct+0x340/0x520
......
Call Trace:
<TASK>
? submit_bio_noacct+0xd5/0x520
submit_bio+0x37/0x60
async_pmem_flush+0x79/0xa0
nvdimm_flush+0x17/0x40
pmem_submit_bio+0x370/0x390
__submit_bio+0xbc/0x190
submit_bio_noacct_nocheck+0x14d/0x370
submit_bio_noacct+0x1ef/0x520
submit_bio+0x55/0x60
submit_bio_wait+0x5a/0xc0
blkdev_issue_flush+0x44/0x60
The root cause is that submit_bio_noacct() needs bio_op() is either
WRITE or ZONE_APPEND for flush bio and async_pmem_flush() doesn't assign
REQ_OP_WRITE when allocating flush bio, so submit_bio_noacct just fail
the flush bio.
Simply fix it by adding the missing REQ_OP_WRITE for flush bio. And we
could fix the flush order issue and do flush optimization later. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: hold queue_lock when removing blkg->q_node
When blkg is removed from q->blkg_list from blkg_free_workfn(), queue_lock
has to be held, otherwise, all kinds of bugs(list corruption, hard lockup,
..) can be triggered from blkg_destroy_all(). |
| In the Linux kernel, the following vulnerability has been resolved:
ubi: Fix possible null-ptr-deref in ubi_free_volume()
It willl cause null-ptr-deref in the following case:
uif_init()
ubi_add_volume()
cdev_add() -> if it fails, call kill_volumes()
device_register()
kill_volumes() -> if ubi_add_volume() fails call this function
ubi_free_volume()
cdev_del()
device_unregister() -> trying to delete a not added device,
it causes null-ptr-deref
So in ubi_free_volume(), it delete devices whether they are added
or not, it will causes null-ptr-deref.
Handle the error case whlie calling ubi_add_volume() to fix this
problem. If add volume fails, set the corresponding vol to null,
so it can not be accessed in kill_volumes() and release the
resource in ubi_add_volume() error path. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix NULL pointer dereference on fastopen early fallback
In case of early fallback to TCP, subflow_syn_recv_sock() deletes
the subflow context before returning the newly allocated sock to
the caller.
The fastopen path does not cope with the above unconditionally
dereferencing the subflow context. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: firewire-digi00x: prevent potential use after free
This code was supposed to return an error code if init_stream()
failed, but it instead freed dg00x->rx_stream and returned success.
This potentially leads to a use after free. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq27xxx: Fix poll_interval handling and races on remove
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item. |
| In the Linux kernel, the following vulnerability has been resolved:
media: max9286: Free control handler
The control handler is leaked in some probe-time error paths, as well as
in the remove path. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fix memory leak if ntfs_read_mft failed
Label ATTR_ROOT in ntfs_read_mft() sets is_root = true and
ni->ni_flags |= NI_FLAG_DIR, then next attr will goto label ATTR_ALLOC
and alloc ni->dir.alloc_run. However two states are not always
consistent and can make memory leak.
1) attr_name in ATTR_ROOT does not fit the condition it will set
is_root = true but NI_FLAG_DIR is not set.
2) next attr_name in ATTR_ALLOC fits the condition and alloc
ni->dir.alloc_run
3) in cleanup function ni_clear(), when NI_FLAG_DIR is set, it frees
ni->dir.alloc_run, otherwise it frees ni->file.run
4) because NI_FLAG_DIR is not set in this case, ni->dir.alloc_run is
leaked as kmemleak reported:
unreferenced object 0xffff888003bc5480 (size 64):
backtrace:
[<000000003d42e6b0>] __kmalloc_node+0x4e/0x1c0
[<00000000d8e19b8a>] kvmalloc_node+0x39/0x1f0
[<00000000fc3eb5b8>] run_add_entry+0x18a/0xa40 [ntfs3]
[<0000000011c9f978>] run_unpack+0x75d/0x8e0 [ntfs3]
[<00000000e7cf1819>] run_unpack_ex+0xbc/0x500 [ntfs3]
[<00000000bbf0a43d>] ntfs_iget5+0xb25/0x2dd0 [ntfs3]
[<00000000a6e50693>] ntfs_fill_super+0x218d/0x3580 [ntfs3]
[<00000000b9170608>] get_tree_bdev+0x3fb/0x710
[<000000004833798a>] vfs_get_tree+0x8e/0x280
[<000000006e20b8e6>] path_mount+0xf3c/0x1930
[<000000007bf15a5f>] do_mount+0xf3/0x110
...
Fix this by always setting is_root and NI_FLAG_DIR together. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix missed ses refcounting
Use new cifs_smb_ses_inc_refcount() helper to get an active reference
of @ses and @ses->dfs_root_ses (if set). This will prevent
@ses->dfs_root_ses of being put in the next call to cifs_put_smb_ses()
and thus potentially causing an use-after-free bug. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: mediatek: common: Fix refcount leak in parse_dai_link_info
Add missing of_node_put()s before the returns to balance
of_node_get()s and of_node_put()s, which may get unbalanced
in case the for loop 'for_each_available_child_of_node' returns
early. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Use correct encap attribute during invalidation
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0 |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: Add !tpm_amd_is_rng_defective() to the hwrng_unregister() call site
The following crash was reported:
[ 1950.279393] list_del corruption, ffff99560d485790->next is NULL
[ 1950.279400] ------------[ cut here ]------------
[ 1950.279401] kernel BUG at lib/list_debug.c:49!
[ 1950.279405] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 1950.279407] CPU: 11 PID: 5886 Comm: modprobe Tainted: G O 6.2.8_1 #1
[ 1950.279409] Hardware name: Gigabyte Technology Co., Ltd. B550M AORUS PRO-P/B550M AORUS PRO-P,
BIOS F15c 05/11/2022
[ 1950.279410] RIP: 0010:__list_del_entry_valid+0x59/0xc0
[ 1950.279415] Code: 48 8b 01 48 39 f8 75 5a 48 8b 72 08 48 39 c6 75 65 b8 01 00 00 00 c3 cc cc cc
cc 48 89 fe 48 c7 c7 08 a8 13 9e e8 b7 0a bc ff <0f> 0b 48 89 fe 48 c7 c7 38 a8 13 9e e8 a6 0a bc
ff 0f 0b 48 89 fe
[ 1950.279416] RSP: 0018:ffffa96d05647e08 EFLAGS: 00010246
[ 1950.279418] RAX: 0000000000000033 RBX: ffff99560d485750 RCX: 0000000000000000
[ 1950.279419] RDX: 0000000000000000 RSI: ffffffff9e107c59 RDI: 00000000ffffffff
[ 1950.279420] RBP: ffffffffc19c5168 R08: 0000000000000000 R09: ffffa96d05647cc8
[ 1950.279421] R10: 0000000000000003 R11: ffffffff9ea2a568 R12: 0000000000000000
[ 1950.279422] R13: ffff99560140a2e0 R14: ffff99560127d2e0 R15: 0000000000000000
[ 1950.279422] FS: 00007f67da795380(0000) GS:ffff995d1f0c0000(0000) knlGS:0000000000000000
[ 1950.279424] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1950.279424] CR2: 00007f67da7e65c0 CR3: 00000001feed2000 CR4: 0000000000750ee0
[ 1950.279426] PKRU: 55555554
[ 1950.279426] Call Trace:
[ 1950.279428] <TASK>
[ 1950.279430] hwrng_unregister+0x28/0xe0 [rng_core]
[ 1950.279436] tpm_chip_unregister+0xd5/0xf0 [tpm]
Add the forgotten !tpm_amd_is_rng_defective() invariant to the
hwrng_unregister() call site inside tpm_chip_unregister(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: use work to update rate to avoid RCU warning
The ieee80211_ops::sta_rc_update must be atomic, because
ieee80211_chan_bw_change() holds rcu_read lock while calling
drv_sta_rc_update(), so create a work to do original things.
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 4621 at kernel/rcu/tree_plugin.h:318
rcu_note_context_switch+0x571/0x5d0
CPU: 0 PID: 4621 Comm: kworker/u16:2 Tainted: G W OE
Workqueue: phy3 ieee80211_chswitch_work [mac80211]
RIP: 0010:rcu_note_context_switch+0x571/0x5d0
Call Trace:
<TASK>
__schedule+0xb0/0x1460
? __mod_timer+0x116/0x360
schedule+0x5a/0xc0
schedule_timeout+0x87/0x150
? trace_raw_output_tick_stop+0x60/0x60
wait_for_completion_timeout+0x7b/0x140
usb_start_wait_urb+0x82/0x160 [usbcore
usb_control_msg+0xe3/0x140 [usbcore
rtw_usb_read+0x88/0xe0 [rtw_usb
rtw_usb_read8+0xf/0x10 [rtw_usb
rtw_fw_send_h2c_command+0xa0/0x170 [rtw_core
rtw_fw_send_ra_info+0xc9/0xf0 [rtw_core
drv_sta_rc_update+0x7c/0x160 [mac80211
ieee80211_chan_bw_change+0xfb/0x110 [mac80211
ieee80211_change_chanctx+0x38/0x130 [mac80211
ieee80211_vif_use_reserved_switch+0x34e/0x900 [mac80211
ieee80211_link_use_reserved_context+0x88/0xe0 [mac80211
ieee80211_chswitch_work+0x95/0x170 [mac80211
process_one_work+0x201/0x410
worker_thread+0x4a/0x3b0
? process_one_work+0x410/0x410
kthread+0xe1/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
igb: clean up in all error paths when enabling SR-IOV
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails. |
